| |
 |
|
|
|
 |
| Detail |
|
 |
| Detail |
| |
 |
Attention:
All the images, schemes and photos are property of Coprel s.a.s. and are under Copyright. |
|
| |
|
|
| Axial Flow Fans - SA Series |
|
|
|
|
|
| Technical Specifications: |
 |
axial-flow fan; |
|
|
Single phase, 2 shaded poles, impedance protected motor, built complying “CE” standards, with self-lubricating and self-aligning sleeve bearings, with big oil reservori; |
|
|
motor with “F” insulation class ( 155°C); |
|
|
suitable for continuous duty with room temperature between -10°C and + 60°C; |
|
|
electric supply by 6,3x0,8mm male faston-type connectors, directly fixed on coil (see the scheme below); |
|
|
fan blade made of aluminium; |
|
|
zincoated metal plate bracket. |
|
| |
| On Request: |
|
fan blades of various diameter and inclination; |
|
|
motors with different power; |
|
|
protection against dust and/or humidity; |
|
|
dustproof end-shields with “IP50” class protection; |
|
|
coil bobbin with “IP56” protection class; |
|
|
operating voltages between 12V and 400V 50/60Hz; |
|
|
2 speeds motor or double voltage version; |
|
|
electric supply with flying cables of various lengths; |
|
|
motor with “H” insulation class ( 180°C); |
|
|
thermal protector or thermal cut off protection; |
|
|
version without supporting plate; |
|
|
spacers of various lengths and/or protruding screws in order to fix the fan on a wall; |
|
|
built complying UL-CSA standards; |
|
|
double shield bearings (ZZ); |
|
|
motor cap made of black nylon mixed with fiberglass. |
|
| |
| ID code: |
| |
|
(*) impregnated versions:
 IV Version: impregnated coil bobbin through immersion in epoxydic varnish (classic impregnation of stators);
PRN Version: coil bobbin spread with black epoxydic resin, the bobbin is protected by a visible layer of resin;
IM Version: the coil bobbin is impregnated through immersion in epoxydic varnish with silicon put in the contacts zone at the end of the winding and 3 cores cable, and the bobbin is covered by a nylon cap. The coil bobbin is not submerged in the resin, but well visible, it should be necessary to pay attention and to place the motor in a way that the open part of the cap will be directed downward in order to prevent that it could fill up of humidity;
INC Version: coil bobbin in “IP56”, the bobbin is completely submerged in the epoxydic resin. |
|
 |
| Faston Position: |
|
|
| View from the protruding driving shaft side |
|
| Dimensions: |
|
 |
|
| Versions: |
|
| Type |
Motor |
Input power |
Dimensions |
Wheel |
Flow rate
M3/h |
RPM |
| A |
W |
A mm |
B mm |
H mm |
| SA 020B |
P20-1 |
0,185 |
25,00 |
53 |
38 |
108 |
Ø 200/26° |
520 |
1000 |
| SA 020C |
P30-1 |
0,310 |
40,00 |
63 |
38 |
108 |
Ø 200/26° |
700 |
1350 |
| SA 020D |
P35-1 |
0,390 |
54,00 |
68 |
38 |
108 |
Ø 200/26° |
900 |
1750 |
| SA 023C |
P30-1 |
0,315 |
42,00 |
63 |
42 |
126 |
Ø 230/22° |
610 |
1050 |
| SA 023D |
P35-1 |
0,400 |
54,50 |
68 |
42 |
126 |
Ø 230/22° |
780 |
1350 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| All motors, fans and blowers are manufactured in our factory in Pieve Emanuele (Milano – Italy). Dimensions and specifications can vary. We reserve ourselves the right to make changes anytime we consider it’s the case. |
|
|
AX Series
