TF/FF Series TFD/FFD Series FF Version extra fixing points   Attention: All the images, schemes and photos are property of Coprel s.a.s. and are under Copyright. Cross Flow Fans TF/FF Series Technical Specifications: Single phase, 2 shaded poles, impedance protected motor, built complying “CE” standards, with self-lubricating and self-aligning sleeve bearings, with big oil reservoir; motor with “F” insulation class ( 155°C); suitable for continuous duty with room temperature between -10°C and + 60°C; electric supply by 6,3x0,8mm male faston-type connectors, directly fixed on coil; ø 60mm fan blade with curved forward pales, made with strengthening intermediate discs, with constant thickness; housing made of zincoated metal plate.   On Request: motor with “H” insulation class ( 180°C); operating voltages between 12V and 400V 50/60Hz; version with double voltage and/or double rotation speed; electric supply with flying cables of various lengths; protection against dust and/or humidity; coil bobbin with “IP56” protection class; thermal protector and/or thermal cut off protection; housing made with superficial cataphoresis treatment; “HT” version for functioning between -30°C and + 100°C; built complying UL-CSA standards; “BB version” with two 626ZZ ball bearings type on the motor; “BBBLV” version with two 626ZZ ball bearings type on the motor and 624ZZ ball bearings type on the fan wheel side; AISI steel driving shaft 420 with milled plane. Motor position: ID code : (point the mouse on the code to visualize the details)   (*) impregnated versions: IV Version: impregnated coil bobbin through immersion in epoxydic varnish (classic impregnation of stators); PRN Version: coil bobbin spread with black epoxydic resin, the bobbin is protected by a visible layer of resin; IM Version: the coil bobbin is impregnated through immersion in epoxydic varnish with silicon put in the contacts zone at the end of the winding and 3 cores cable, the bobbin is covered by a nylon cap. The coil bobbin is not submerged in the resin, but well visible, it should be necessary to pay attention and to place the motor in a way that the open part of the cap will be directed downward in order to prevent that it could fill up of humidity; INC Version: coil bobbin in “IP56”, the bobbin is completely submerged in the epoxydic resin. TF Dimensions: TF Versions: Series Motor Dimensions Input power W Input current A Free air RPM Free air flow rate Static pressure PA A B C D H I TF90/15 15-1 156 64 94 104 15 53.5 18 0,140 1900 60 60 TF90/20 20-1 162 64 94 104 20 58.5 23 0,150 2400 80 62 TF120/15 15-1 186 94 124 134 15 53.5 19 0,160 1600 85 58 TF120/20 20-1 191 94 124 134 20 58.5 24 0,170 2150 110 62 TF180/15 15-1 246 154 184 194 15 53.5 19 0,150 1300 100 55 TF180/20 20-1 251 154 184 194 20 58.5 25 0,180 1600 125 60 TF180/30 30-1 261 154 184 194 30 68.5 37 0,280 2400 180 63 TF180/35 35-1 266 154 184 194 35 73.5 42 0,320 2550 200 65 TF240/20 20-1 311 214 244 254 20 58.5 25 0,190 1250 125 55 TF240/35 35-1 326 214 244 254 35 73.5 46 0,340 2500 240 64 TF270/20 20-1 341 244 274 284 20 58.5 26 0,200 1100 130 53 TF270/35 35-1 356 244 274 284 35 73.5 49 0,350 2250 260 63 TF300/20 20-1 371 274 304 314 20 58.5 25 0,195 1200 171 51 TF300/30 30-1 381 274 304 314 30 68.5 43 0,320 1900 270 61 TF300/40 40-1 391 274 304 314 40 78.5 53 0,400 2300 330 64 TF360/20 20-1 431 334 364 374 20 58.5 26 0,195 1050 180 48 TF360/30 30-1 441 334 364 374 30 68.5 45 0,325 1700 285 60 TF360/40 40-1 451 334 364 374 40 78.5 55 0,450 2200 370 62 FF Dimensions: FF Versions: Series Motor Dimensions Input power W Input current A Free air RPM Free air flow rate Static pressure PA A B C E F H I FF90/15 15-1 156 64 94 103 112 15 53.5 18 0,140 1900 60 60 FF90/20 20-1 162 64 94 103 112 20 58.5 23 0,150 2400 80 62 FF120/15 15-1 186 94 124 133 142 15 53.5 19 0,160 1600 85 58 FF120/20 20-1 191 94 124 133 142 20 58.5 24 0,170 2150 110 62 FF180/15 15-1 246 154 184 193 202 15 53.5 19 0,150 1300 100 55 FF180/20 20-1 251 154 184 193 202 20 58.5 25 0,180 1600 125 60 FF180/30 30-1 261 154 184 193 202 30 68.5 37 0,280 2400 180 63 FF180/35 35-1 266 154 184 163 202 202 35 42 0,320 2550 200 65 FF240/20 20-1 311 214 244 253 262 20 58.5 25 0,190 1250 125 55 FF240/35 35-1 326 214 244 253 262 35 73.5 46 0,340 2500 240 64 FF270/20 20-1 341 244 274 283 292 20 58.5 26 0,200 1100 130 53 FF270/35 35-1 356 244 274 283 292 35 73.5 49 0,350 2250 260 63 FF300/20 20-1 371 274 304 313 322 20 58.5 25 0,195 1200 171 51 FF300/30 30-1 381 274 304 313 322 30 68.5 43 0,320 1900 270 61 FF300/40 40-1 391 274 304 313 322 40 78.5 53 0,400 2300 330 64 FF360/20 20-1 431 334 364 373 382 20 58.5 26 0,195 1050 180 48 FF360/30 30-1 441 334 364 373 382 30 68.5 45 0,325 1700 285 60 FF360/40 40-1 451 334 364 373 382 40 78.5 55 0,450 2200 370 62 Static Pressure Courve:   All motors, fans and blowers are manufactured in our factory in Pieve Emanuele (Milano – Italy). Dimensions and specifications can vary. We reserve ourselves the right to make changes anytime we consider it’s the case.
	©  Copyright 2007 Coprel S.r.l. All brands, product labels and companies are property of their respective owners. Developed by internetlandia